Premium Sound – 4 Full range tweeters + 1 Subwoofer +1 Assisted bass resonator. Charging capability - built-in charger ensures jobsite productivity by charging 12V MAX* and 20V MAX* DEWALT® power tools IP54. Rated for water and dust resistance. Connectivity to Bluetooth®, 3.5mm Aux. Input, 5V/1A USB chargerToughSystem. Carrier cart compatible. Can be stacked to other ToughSystem® modules. Can run on a 12V MAX* or 20V MAX* DEWALT® Li-ion power tool battery or can be plugged into a wall outlet. With respect to 12V MAX* - Maximum initial battery voltage (measured without a workload) is 12 volts. Nominal voltage is 10.8.*With respect to 20V MAX* - Maximum initial battery voltage (measured without a workload) is 20 volts. Nominal voltage is 18.

GREENLEE digital readout temperature gun switchable from Fahrenheit to Celsius. Comes with case.

Campbell Hausfeld 3 Gallon Air Compressor has a peak HP of 1/3. Maximum PSI of 100. Includes a 25' recoil hose.

Metal gear housing for jobsite durability and increased reliability. Depth-sensitive, set and forget-nosepiece for consistent fastener depth Rubber grip and two-finger trigger for increased comfort and greater control. Helical-cut steel, heat-treated steel gears for long life and durability Lightweight with excellent ergonomics

Mastercraft Hammer Drill offers a 6 Amp motor. 1/2" keyed chuck. Selection switch allows user to select rotation only, or rotation with hammering operation. Lock on button helps reduce fatigue during extended use

Compact size to fit into tight spots. Weighs 4.7 pounds. Dual speed range (0-to-450 RPM and 0-to-1,500 RPM). High-performance motor delivers up to 380 unit watts. Comes with 2 batteries charger and carrying case.

Compact, lightweight design fits into tight areas High performance motor delivers 300 unit watts out (UWO) of power ability completing a wide range of applications. High speed transmission delivers 2 speeds (0-450 and 1,500 rpm) for a range of fastening and drilling applications. 1/2-Inch single sleeve ratcheting chuck provides tight bit gripping strength. Ergonomic handle delivers comfort and control. Tool Width: 1.9 inches. Tool Height: 6.5 inches

3-beam line laser to aid in 90 Degree layout. 2x brighter diode to increase visibility in bright job site conditions. Built-in magnetic pivot bracket mounts easily on metal surfaces. Accurate to +/- 1/8-inch at 30 ft. for level applications. 1-button operation and control panel for ease of use Micro adjust knob for precise alignment of 90 Degree intersecting lines over greater distances

RIDGID Die cast construction for increased durability. Spindle lock for quick, easy accessory changes. 3-position side handle for added convenience. Powerful 13 amp motor and precision cut gears. MISSING SCREW ON HANDLE.

3 DRILLING MODES: You can switch between driving, drilling, and hammer drilling modes to let this tool tackle softwoods, hardwoods, masonry, and even some metals with the help of the 18-position clutch. LED LIGHTING: Keep your work illuminated with the LED panel under the keyless chuck that prevents shadows from forming, so you can focus on the task at hand. AMBIDEXTROUS BELT CLIP: You can screw the included belt clip onto either side of the tool, letting you store it on your belt within easy access, no matter your handedness ALL METAL GEAR CASING: You’ll be relieved that this tool comes so strongly constructed when you’ve dropped it on the job and the motor keeps running at full speed. TOOL ONLY

MILWAUKEE The M18 Cordless 2-Speed 1/4-inch Hex Impact Driver is the most powerful 1/4-inch hex compact impact driver in its class and offers the best power to size ratio among like competitors. Featuring a Milwaukee built 4-Pole frameless motor and optimized impact mechanism, this impact driver delivers up to 2,750 RPM, 3,450 IPM and 1,500-inch lbs. of fastening torque for class-leading performance. This is the only tool in its class to offer multiple speed/torque modes through proprietary 2-Mode DRIVE CONTROL. REDLINK Intelligence provides optimized performance and overload protection using total system communication between tool, battery and charger. The M18 Cordless 1/4-inch Hex Impact Driver features an LED Light to illuminate work surfaces, and includes an all-metal, reversible belt clip for temporary tool storage.TOOL ONLY

Sealed aluminum head: Designed for impact- and weather-resistant durability. 135 degree rotating head: Provides flexible, focused illumination. Integrated hook: Leaves both hands available for work anywhere on the jobsite. Flashlight only - battery and charger sold separately. In easy-to-open packaging to pass the savings on to you.

UNIVERSAL ADAPTOR: You can use accessories from other multi tools with the universal adaptor that screws onto the head 12 SPEED SETTINGS: Switch between 5,000 and 20,000 orbits per minute with the speed adjustment knob. Keep this tool suitable for a variety of different applications SANDING: An included sanding head with sanding pads will let you put the finishing touches on your woodworking projects without a separate purchase. GROUTING: The multi-purpose head can slice into tight spaces to clear grout or trim FUEL GAUGE: Know how much time you have left on your job with the LED panel on the side of the unit. It tell you how much battery you have left in 25% increments. TOOL ONLY

DEWALT Compact, lightweight design fits into tight areas3 LED lights provide visibility without shadowsOne-handed loading 1/4" hex chuck accepts 1" bit tipsBelt hook included for portability. 12 Volt 1/4" impact driver set with 2 batteries and charger.

2 new DEWALT 20 VOLT Lithium ion rechargeable batteries with fuel gauges.

MILWAUKEE 1/2" hammer drill and 1/4" hex impact driver, 2 M18 red lithium XC batteries, charger and carry bag.

MILWAUKEE M18 red lithium XC battery.

DEWALT 20 volt XR lithium ion battery.

DEWALT 20 volt rechargeable 5 amp/hour battery.

Powerful 4.0 maximum HP, 15-amp motor: Delivers 6,000 RPM for faster grinding Spiral bevel gearing: Optimizes performance and durability Ergonomic handles: Angled rear and side handles promote natural hand positions and increase user comfort 3-position side handle: Attaches in 3 locations to maximize user control 2-finger trigger switch: Offers convenience for continuous-use applications 9-ft. 2-wire fixed rubber cord: Durable construction for longer tool life 2-in-1 versatility: Converts to a sander for greater tool utility

Powerful 5 Amp motor with Max output of 630 Watts (120V). No-Load speed of 11,000 RPM Spindle lock, provides easy and quick disc changes. External brush caps allowing for quick in-field service of brushes. Ball bearing construction for smooth operation and long life Tool rest, conveniently located to protect the switch from accidentally turning on and prolonging tool life. Slide switch, easy to use with a quick-off feature to shut the tool off immediately for added safety. Removable side handle, improves control and comfort. 3.1 lbs, lightweight design facilitates maneuverability and is excellent for overhead applications

SDS-plus bit system provides tool-free bit changes with automatic bit locking and dust protection. Multi-function selector with3 modes of operation, rotation only, rotary hammer, and hammer only. Variable-speed reversing trigger for accurate bit starting as well as removing fasteners or bound bits. Vario-Lock positioning rotates and locks chisel into 36 different positions to optimize working angle. D-handle design for extra control, ideal for overhead and downward drilling applications. Comes complete with storage case

Lightweight at just 7.3 lbs. Power to drive nails up to 3-1/2 in. x 0.131 in. into engineered lumber Tool-free adjustable exhaust. Accepts 30 degree to 34 degree paper tape offset round head and clipped head nails from 2 to 3-1/2 in. Operating pressure of 70-120 PSI

Tool-free jam release mechanism for easy nail removal. Tool-free adjustable exhaust channels contaminants away from the user, 100 nail magazine capacity. Sequential firing mode

Makita 5 piece kit. Comes with Makita carry case 2 18 volt 3.0 AH batteries (the bigger ones), drill, impact driver, sawzall, circular saw, light and charger.

Milwaukee 10 inch sliding compound miter saw. Comes with hold down fixture and adjustable sliding backrest.

Bosch 10 inch 15 amp miter saw.. All-metal bevel lock lever and range selector located upfront for quick and easy bevel settings without reaching behind the saw. Microfine miter adjustment for fractional measurements outside of miter detents. Large 22-1/4 in. base with integrated base extensions - extends material support up to 37-1/4 in.Two tall 4 in. x 10 in. speed-track sliding fences for easy bevel cut set-up

Band Saw has a max cutting width of 9".120V band saw with 2.5 A motor, and 2556 spm cutting capacity. With a 3-1/8" cutting depth. Table tilting range of 0º- 45º. On - off self locking switch provides the bandsaw with added safety

SKILSAW professional 10 inch 15 amp miter saw with blade in working condition.

15.0 Amp/4.0 HP (maximum motor HP) motor provides overload protection, increasing performance and durability. Ergonomically designed "D" handle provides a more comfortable hand position, reducing fatigue and increasing productivity. Steel base allows user to weld jigs or stops directly onto the base

Oil lubricated: Cooler running pump, minimizes wear. Durable cast iron cylinder reduces wear and increases pump life, removable for easy maintenance. Built-in thermal overload for additional motor protection. Large automotive style industrial air filter for increased air intake and greater efficiency. Powerful 2.5 HP 4-Pole motor produces 4.2 CFM at 90 PSI for increased productivity and lower noise

Light-weight tool designed for today's paint finishes. Use with 3M™ Finesse-it™ Polishes and Foam Buffing Pads for a uniform finish 3M™ Gripping material for greater operator comfort. This is the two handed (PN 28333) version. Arbor hole accommodates mandrel tool attachment used by a variety of tools. This powerful .26 HP motor tool is designed for use in general paint shop applications for buffing or polishing. Includes a 3M™ Hookit Disc Pad. Lightweight, balanced tool designed for paint shop applications for buffing or polishing today's paint finishes. Use with 3M™ Finesse-it™ Polishes and Foam Buffing Pads for a uniform finish. Retails for over $500.00

Starrett 3" - 4" digital micrometer. New in box with wood case, original box, 2 gauges, all paperwork and wrench.

NEW DeWALT® Masonry Drill, 2-Cutter, 5/8 in Dia, 17 in Cutting Depth, 2 Flutes, U-Flute Flute, 17 in Flute Length, 3/4 in Shank, Spline Shank, Right Hand Cutting, Carbide Cutting Edge, Steel, Bright, Applicable Materials: Concrete and Masonry.

Procut 1 3/4 Inch HS TS counterbore CF50148 Retails for over $100.00. New in box

Most powerful and versatile rotary tool in the Dremel line. EZ Change system-change all Dremel accessories without the wrench or collet lock. Cooler running with 20-percent more air flow in venting design. Variable speed of 5,000 - 35,000 RPM with electronic feedback. Includes 6 attachments and 40 accessories for maximum versatility.

Master Craft 6 inch digital calipers

The Bosch 1297D quarter-sheet orbital finishing sander pulls regular sandpaper flat and tight for fast and easy installation; efficient, uniform sanding, and longer paper life. It also accepts stick-on paper. The Microfilter dust canister efficiently filters and captures sanding dust. For user comfort, the sander features a tapered top, and the 3-point counterbalance minimizes the vibration for maximum comfort.

Power Fist blocking hammer.

Power Fist Air micro grinder

2 Graco and a Wiwa spray gun with extra parts.

MAC ATPQ40, Features low noise technology. 8-Position guard adjustment (126° radius). Cushion-grip to reduce vibration. Safety lock for swivel guard. Rear exhaust. Rotating air inlet: 0.7 HP. Safety throttle lever.

MAC AD540 used reversible 3/8 inch air drive drill. Lightweight and small to get into tight spaces.

Free Speed: 1800 rpm. Air consumption: 4 CFM Air Inlet: 1/4". Operation Pressure:90 psi Minimum Hose Size 3/8"

Blue Point AT 215 angle grinder. Excellent for working in confined areas on jobs that require fast metal removal. Ideal for body shops, automobile and truck repair. Grease Fitting in Head Enables gears to be greased for longer tool life. Moveable guard, up to 50° in either direction fitting various applications. Built in speed regulator allows user to set desired speed providing more control. Rear exhaust with rotating deflector directs air away from work area with no blow back at user. Comfort Grip Housing Insulate from cold and vibration for less user fatigue. Safety Lever Throttle Prevents accidental start ups for increased safety

5 laser points: Upwards and downwards plumb laser with extendable foot and 3 horizontal points which form two 90° angles. Optimal for setting out and transferring right angles. For the transfer of the layout from the floor to the ceiling, for both straight and curved walls. For rapid and accurate alignment. 20 hours operating period with 3 AA batteries. Comes with carrying case.

Husky air chisel grab some bits hook up to a compressor and go.

Pro Point laser kit. Comes with laser, laser holding head, tripod and glasses all in an easy to carry case

Ultimate sensitivity 5 ? 50ppm. Detects dangerous explosive gases. Instantaneous response. Used in almost any situation where combustible gasses, vapor or residues need to be found. Automatic warm up. Adjustable sensitivity. Comes complete with case

Adjustable power regulation for optimal control of fastener settings. Automatic piston return and cartridge advance.

Dewalt 20 volt 6.0 AH Lithium ion max 60 volt replacement battery

The Bosch GLL 3-50 Three-Line Laser with Layout Beam produces one horizontal line, two vertical lines plus plumb down point - for level, align, plumb and square applications to help users swiftly measure the job with precision. The included a 360° rotational telescoping mounting base helps users effectively set right angles up to 33 Ft. without having to reset. The base has manual fine adjustment, which allows for easy setup and convenient viewing of the laser point on the floor. The Smart Pendulum System self-levels and indicates out-of-level condition. It offers an accuracy of 3/8 In. up to 100 Ft., and it has a pulse mode, for use with the optional LR2 laser receiver, to extend its range up to 165 Ft.

Makita 4.0 AH 18 volt lithium ion replacement battery

Makita 18 Volt Lithium Ion 1.5 AH battery

Dewalt 20 volt Lithium Ion Max VR battery

Bosch 3.0 amp hour 18 volt battery

Diamond blade 10" X .060 X 1 5/8" WET ONLY blade. These diamond blades are used to cut ceramic tile and marble and are used in electric water cooled tile cutters. NEVER USED.

Charge DEWALT® batteries from your vehicle's power outlet (except Univolt®). Automatic shut-off protects excessive discharge of vehicle's battery. Charges in 1 hour or less. Fan-cooled battery and charger technology increases run-time and number of recharges. Charges all DEWALT® 24V batteries so 24V users need only one charger.

THIS COIL ROOFING NAILER HAS A DURABLE ALUMINUM HOUSING AND A ONE-DOOR LOADING SYSTEM FOR FAST RELOADING. IT HAS A DRY-FIRE LOCK OUT TO PREVENT DRY FIRING AND TO ALERT THE USER TO RELOAD THE MAGAZINE. DEPEND ON THIS COIL ROOFING NAILER FOR DURABILITY AND COMFORT.

TheMastercraft 6A Compact Reciprocating Saw features variable speeds (0–2700 SPM) and 25/32" (2 cm) blade stroke for fast and efficient cutting. Tool-free blade change for fast and easy, one-handed blade changes. Adjustable shoe pivots, offering increased control and greater contact with the cutting surface. Rubber overmoulded non-slip handle and boot for a more secure grip and control.

This Makita 18V reciprocating saw offers users a powerful performance with help from Lithium-Ion battery technology. The variable speed feature keeps you in complete control of the saw's cutting speed while the tool-less blade change system allows for quick blade switches. Ergonomic soft rubber grip design for vibration absorption and comfortable operation. One-handed fast tool-less blade changes Increased cutting speed and stroke length offers maximum cutting efficiency. Newly designed vertical crank mechanism minimizes blade deflection and reduces vibration. Battery and charger sold separately.

The RIDGID 5 in. Random Orbit Sander features an electronic speed control dial for maximum control for different applications. It has a variable no-load speed of 7000-12,000 RPM and a permanent magnet motor to maintain constant speed and power under load applications. Its onboard vacuum adapter fits standard 2-1/4 in. or 2-1/2 in. hoses for a cleaner, virtually dust-free work environment.

Variable speed 3.3 Amp motor , 4,500-12,000 OPM Random orbit sanding action - Eccentric orbit plus rotation for aggressive stock removal and swirl-free finishing High-performance microcellular backing pad - Conforms to contours, provides a fine finish Bosch microfilter dust canister with integrated paper filter - Optimal filtering system of fine dust; through-the-pad dust extraction for cleaner workspace Integral pad dampening system - Helps prevent swirl marks for a consistent fine finish Variable-speed dial with Soft Start - Allows match of speed to workpiece and task and reduces start-up torque Constant Response circuitry - Maintains constant speed under load, provides overload protection Ergonomic handles, tapered Soft-Grip top - Multiple grip positions provide comfort and control; front handles removes easily for sanding in tight spots Trigger with lock-on button - For extended period of use Uses 8-hole 5" hook and loop discs - Compatible with industry-standard discs Rugged die-cast aluminum gear housing with exclusive dual-bearing pad mount - Long-life design eliminates wobble and vibration

10 inch Craftsman buffer/polisher great for cars and boats

This Mastercraft® Coil Roofing Nailer drives full-head or round-head 3/4 to 1 3/4" (19 to 45 mm)long nails. Strong, lightweight aluminum frame For use with standard 15° wire-collated roofing nails Nail Capacity: 2 strips (up to 120) Soft grip for comfort and control. Bump firing model for fast fastening Trigger lock-off allows trigger to be disable when not in use. With case and accessories.

Powerful 8-amp motor, 0 to 850 rpm, variable speed control All metal grip-lok single sleeve keyless chuck for a stronger hold on the bit and all metal gear case and diaphragm. Ergonomic tactile grip and 2 finger trigger for user comfort and balance.

7.5 Amp - for faster cutting and tougher applications. Faster speed of cut - rip through plywood and cut more metal. 3-in-1 tool - go beyond cutting and flush cutting with surface preparation applications including rust, paint, and thinnest removal. Added durability - improved drive-train lasts 3x longer than the Saw-Max and its metal foot and guard handle tough applications, Excellent line of sight for precise, confident cuts.

Compact ergonomic design- contoured grip increases comfort and control to drive screws all day Posi-Lok™ Nose Piece design retains depth setting when removed and eliminates time consuming depth readjustments Plastic gear housing provides lightweight design Strong bit tip magnet maximizes control when driving long screws Variable speed trigger with forward-reverse lever for increased control Lock-on button for extended-use applications Belt clip frees up hands for other important tasks

RIDGID 55442-1 3/8" CORDED 8 AMP CHUCK LESS DRILL

Mastercraft 5A Drill/Driver features a variable speed range of 0-2,700 RPM for a variety of drilling and driving projects 3/8" keyless chuck for quick and easy bit changes Lock-on button helps reduce fatigue during prolonged use Forward/reverse switch for convenient one-handed use Rubber non-slip grip for added comfort and control Built-in belt clip hooks conveniently onto a tool belt

Full wave electronic variable speed motor with soft start runs at 8,000-24,000 rpm with constant speed under load to ensure a quality finish in all materials Rack and pinion depth adjuster, with micro-fine adjusting allows quick, accurate set-up Integral dust collection system efficiently removes chips and provides superior bit visibility Spindle lock button allows for single-wrench bit changes Innovative rubber-coated knobs have plunge-lock and on/off built-in for maximum user control; 1/4-inch - 1/2-inch collet capacity for greater versatility

11 Amp motor delivers forcible output power (2,000W) for the toughest grinding jobs Low-Profile head, Permits access in tight areas Dust-Proof construction prolongs armature, Switch and bearing life Dust seal, Prevents dust from entering the ball bearing on the commutator side Removable side handle, Improves control and comfort Trigger Lock-On for comfortable continuous operation 6.2 lbs Compact and lightweight design facilitates maneuverability and is excellent for overhead applications

Battery not included. 2-speed settings for matching power to the task. All metal gears for extended tool durability. 1/2 in. single sleeve ratcheting chuck to hold bits secure in high torque applications. 24-position clutch ring allows adjustments to match torque to application. Hex-grip micro texture for added user comfort.

Cordless drill, No battery. All Metal Gears - for extended job site durability. 1/2 in. Single Sleeve Ratcheting Chuck - holds bit tight and secure Powerful 2-Speed Settings - for matching power to the task. 24-Position Clutch Ring - Allows adjustments of clutch to match torque to application. Hex-Grip Innovative - micro texture for secure grip and maximum user comfort.

Extremely compact, the DeWalt DW056 cordless impact driver lets you easily access tight spaces. The DeWalt driver can perform a variety of fastening applications, thanks to its maximum torque of 1,170 in.-lbs. With speeds of 0-2,400 rpm and 0-3,000 bpm, this cordless impact driver enhances your productivity. As it has a lightweight design, this DeWalt driver reduces user fatigue. Moreover, the textured anti-slip comfort grip of the DeWalt DW056 gives you a firm and comfortable hold.

This unit is ideal for plumbing, automotive repair and construction for inspection of hard-to-reach or hard-to-see areas. The camera has a 3 1/2" colour LCD screen. LED lights inside the camera probe tip illuminate dark spaces. The 9mm dia. x 36-inch flexible camera probe is waterproof and comes with a sturdy carrying case.

NEW IN BOX Powerstate Brushless Motor supplies constant power for faster cuts and reduced heat for extended life. Compact size allows for cutting in tight spaces, and light weight makes overhead work easier. One-handed design provides superior control and versatility over a standard recip saw. One (1) Milwaukee M12 Fuel Hackzall bare tool new in box.

Dual trigger design incorporates safety and comfort for all day use Drives both heavy duty 3/8-in crown staples from 1/4-in to 9/16-in, and 18 ga brad nails from 1/2-in to 5/8-in for a wide range of applications. Oil-Free operation requires no regular maintenance and eliminates the risk of oil stains. Durable lightweight die-cast aluminum design Bottom loading for quick reloads.

Makita Nibbler JN1601 Clean and precise work in keystone plate, deck plate and other corrugated sheet materials. Die rotates 360°. Large 1/4"" stroke. Ergonomic, slim body design for easy gripping. Extremely light (weighs only 3.6 lbs.) for easy handling.Overall Length : 10.25 inches. Lock-on sliding switch for continuous operation. Built-in thickness gauge for convenience Easy punch and die replacement for reduced down time

Make easy work of cutting through concrete and similar materials with this rugged gas powered cut-off saw from Wacker! Features: Model: BTS-1030-L3. Approximate measurements: 31"L x 14.5"H x 11"W 10" blade. Plastic body housing. Trigger operation with safety. Gas powered.

Ordered and never used at over $400.00. Spool Gun 3035-20 For use with the Handler 140 and 187 (requires SGA 100 spool gun control) Also for use with the IronMan 210 (direct connection) The Hobart Spool Gun 3035-20 is lightweight, compact and well-balanced. This reliable, yet economical gun provides 20 ft (6.1 m) of cable and gas hose for extended reach. The 3035-20 spool gun features easily accessible drive rolls with a screw-style tension adjustment and smooth feeding of aluminum, steel and stainless steel wires.

The TS 410 is a lean, clean, cut-off machine that’s easy to use and easier to maintain. Just squeeze the trigger and watch its 12” cutting wheel grind through iron, steel, concrete and expectations. Part of the STIHL Cutquik series, this model features advanced filter technology that automatically handles daily maintenance. Its revolutionary X2 air filtration removes 99.96% of particles from air entering the carburetor and engine, making its onboard filters virtually maintenance free. Good thing it has anti-vibration system to maximize comfort – a feature you’ll appreciate after a full day of cutting concrete.

36.3 cc professional-grade, 2-stroke engine for outstanding performance. The I-30 starting system for reduced effort starting Automatic, adjustable oiler to match cutting conditions. G-Force Engine Air Pre-Cleaner™ for reduced air filter maintenance Heavy-duty, easy-access, automotive-style air filter for superior filtration.

Modular dust proof design is easy to service. Grease packed lubrication for longer life. Comfortable shock absorbing handles. More impact energy 16 joules. Fast chipping speed. Hexagon drive. 1/2 inch spline shank drill/rotary hammer.

Rotary Hammer Drill combines working comfort with the power you need. Comes with original case.